RSS Feed
Knowledgebase : BaseManager Online Help > Working with Programs
NOTE: If you are using BaseManager with a BaseStation 3200 V16 controller, see the updated help. [https://www.baselinesystems.com/help/BaseManager_Help/Content/Setup_Operation/programs_schedules/add-program-3200.htm] * Make sure that the controller on...
* Make sure that the controller from which you want to delete a program is displayed in the BaseManager footer. To select a different controller, click the Menu icon in the upper-left corner of the BaseManager page, and then click SITES AND CONTROLLERS....
With one or more flow devices, the irrigation controllers have the ability to do a learn flow cycle to determine the flow for the zones of a program. From BaseManager, you can run a learn flow cycle on one program at a time. When the learn flow cycle be...
* Make sure the controller that you want to view the report for is displayed in the BaseManager footer. To select a different controller, click the MENU icon in the upper-left corner of the BaseManager page, and then click SITES AND CONTROLLERS. Continu...
* Make sure the controller that has the program that you want to view is displayed in the BaseManager footer. To select a different controller, click the Menu icon in the upper-left corner of the BaseManager page, and then click SITES AND CONTROLLERS. C...
When a start event is reached, the program with the highest priority gets first call on the water and time. A higher priority program "preempts" lower priority programs and runs to completion before the lower ones. * Make sure that the controller on w...
* Make sure that the controller on which you want to manually start/stop a program is displayed in the BaseManager footer. To select a different controller, click the MENU icon in the upper-left corner of the BaseManager page, and then click SITES AND C...
NOTE: In the flow model associated with the BaseStation 3200 V16 firmware, you do not add a mainline to a program. Instead you assign zones to a mainline, and then you put those zones in a program. If you are using BaseManager with a BaseStation 3200 V16 ...
* Make sure that the controller on which you want to set up a booster pump for a program is displayed in the BaseManager footer. To select a different controller, click the Menu icon in the upper-left corner of the BaseManager page, and then click SITES...
You can make changes to the seasonal adjustment settings in a program when you are adding a new program or changing an existing program on a BaseStation 1000 or BaseStation 3200 controller. If your area is experiencing a period of unseasonably dry or we...
The BaseStation 1000 can manage one complete water source (master valve, flow sensor, and pump start) and can be upgraded to support up to three water sources. If your controller has been upgraded to support multiple water sources, you can associate a s...
You can learn flow for a zone from the MAPS tab, from QUICK VIEW, or from the PROGRAMS tab. LEARNING FLOW FOR A ZONE FROM THE MAPS TAB * Make sure that the controller on which you want to learn flow for a zone is displayed in the BaseManager footer. ...
You can make changes to the water window settings in a program when you are adding a new program or changing an existing program on a BaseStation 1000 or BaseStation 3200 controller. Water windows are used to select when watering will or will not be all...
Use this option to associate a master valve or pump start biCoder with a program. Before you perform this procedure, you must assign a biCoder as a master valve or pump biCoder. Refer to Assigning Master Valves [http://support.baselinesystems.com/support/...
You can make changes to the soak cycle settings in a program when you are adding a new program or changing an existing program on a BaseStation 3200 controller. * Make sure that the controller on which you want to add or change a program is displayed ...
When you create a program, you either need to have it start at specific times, or you need to configure a start condition based on the state of a device. In some cases, you might want to have both a scheduled start time and a start condition. To learn m...
You can make changes to the zone settings in a program when you are adding a new program or changing an existing program on a BaseStation 3200 controller. * Make sure that the controller on which you want to add or change a program is displayed in the...
You can make changes to the start, stop, pause conditions in a program when you are adding a new program or changing an existing program on a BaseStation 1000 or BaseStation 3200 controller. You can set up a condition to start, stop, or pause a program ...
NOTE: If you are using BaseManager with a BaseStation 3200 V16 controller, see the updated help. [https://www.baselinesystems.com/help/BaseManager_Help/Content/Setup_Operation/programs_schedules/add-program-3200.htm] * Make sure that the controller on...
You can make changes to the soak cycle settings in a program when you are adding a new program or changing an existing program on a BaseStation 1000 controller. * Make sure that the controller on which you want to add or change a program is displayed ...
If you have not added any programs on your BaseStation 1000, refer to Adding a Program [http://support.baselinesystems.com/support/index.php?/Knowledgebase/Article/View/131/38/adding-a-program] in the BaseManager Online Help, or refer to Setting Up Progra...
You can make changes to the concurrent zones settings in a program when you are adding a new program or changing an existing program on a BaseStation 1000 or BaseStation 3200 controller. IMPORTANT! The number of concurrent zones allowed on your controll...
When you configure a zone to use WeatherAccess, you do not enter minutes in the Water Time field in the Zone Setup screen on the controller. Instead, the time is calculated based on the zone settings, weather, and rainfall data received from BaseManager f...
You can make changes to the zone settings in a program when you are adding a new program or changing an existing program on a BaseStation 1000 controller. * Make sure that the controller on which you want to add or change a program is displayed in the...